Digi Tech RP1000 Manual do Utilizador Página 38
- Página / 56
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
34
To use the Looper with a quiet start, follow these steps:
Press the 1. Looper button to enable the Looper. The Looper button should now be lit.
None of the Record, Play, Overdub LEDs will be lit at this time.
To begin looping, press the 2. Down footswitch. The Record LED on the matrix will flash
red indicating the Looper is armed and ready to record but not actually recording yet.
To begin recording, just start playing. The 3. Record LED will now light solid red indicating
recording is in progress.
To set the loop point, press the 4. Down footswitch again. The loop point will be set and
the recorded phrase will now begin playback. The Record LED will turn off and the green
Play LED will now be lit.
To add overdubs to the loop, press the 5. Down footswitch again. The yellow Overdub LED
will now light (the green Play LED will still be lit) indicating that anything being played will
be merged with the loop being played.
Press the 6. Down footswitch again to stop overdub recording which will turn off the Over-
dub LED and return the loop to normal playback.
To stop loop playback, press the 7. Up footswitch. This does not clear out the loop but sim-
ply stops playback. Pressing the Down footswitch again will resume playback.
To clear a loop from memory, press and hold the 8. Up footswitch until the main display
shows
.
To use the Looper on the fly, follow these steps:
Press the 1. Looper button to enable the Looper. The Looper button should now be lit.
None of the Record, Play, Overdub LEDs will be lit at this time.
Start playing your guitar. 2.
To begin looping, press the 3. Down footswitch. The Looper will start recording as soon as
you press the Down footswitch, and the Record LED on the matrix will light red after
about half a second.
To set the loop point, press the 4. Down footswitch again. The loop point will be set and
the recorded phrase will now begin playback. The Record LED will turn off and the green
Play LED will now be lit.
To add overdubs to the loop, press the 5. Down footswitch again. The yellow Overdub LED
will now light (the green Play LED will still be lit) indicating that anything being played will
be merged with the loop being played.
Press the 6. Down footswitch again to stop overdub recording which will turn off the Over-
dub LED and return the loop to normal playback.
To stop loop playback, press the 7. Up footswitch. This does not clear out the loop but sim-
ply stops playback. Pressing the Down footswitch again will resume playback.
To clear a loop from memory, press and hold the 8. Up footswitch until the main display
shows
.
If using the optional FS3X to control the Looper, follow these steps for a quiet start:
To begin looping, press the 1. Down footswitch. The Record LED on the matrix will flash
red indicating the Looper is armed and ready to record but not recording yet.
To begin recording, just start playing. The 2. Record LED will now light solid red indicating
recording is in progress.
To set the loop point, press the 3. Down footswitch again. The loop point will be set and
the recorded phrase will now begin playback. The Record LED will turn off and the green
Play LED will now be lit.
To add overdubs to the loop, press the 4. Down footswitch again. The yellow Overdub LED
will now light (the green Play LED will still be lit) indicating that anything being played will
be merged with the loop being played.
Press the 5. Down footswitch again to stop overdub recording which will turn off the Over-
dub LED and return the loop to normal playback.
To stop loop playback, press the 6. Up (right) footswitch. This does not clear out the loop
but simply stops playback. Pressing the Down (left) footswitch again will resume playback.
To clear a loop from memory, press and hold the 7. Mode (left) footswitch until the main
display shows
.
- Integrated 1
- Effects Switching 1
- Table of Contents 3
- Warranty 4
- Section One - Introduction 5
- Tone Library (Knob 1) 6
- Effects Library (Knob 2) 6
- Effects Level (Knob 3) 6
- A Guided Tour of the RP1000 8
- Rear Panel 11
- Getting Started 12
- Connection Setups 13
- Stereo Amps 14
- Amp Loop with Pre-Amp In Line 15
- Stomp Loop 15
- Amp Loop and Stomp Loop 16
- Applying Power 18
- Editing/Creating Presets 19
- Editing Amp/Cabinet Models 19
- Amp/Cabinet Bypass 19
- 1. Press Store; 20
- characters in Display 20
- flash individually 20
- 2. Use Knobs to 20
- name Preset 20
- About the Effects 21
- Effect Denitions 21
- Distortion 22
- Amplier 24
- Noise Gate/Auto Swell 26
- Chorus/FX 26
- Expression Pedal 35
- Footswitch Assign 35
- Wah Min/Max 36
- Expression Update 36
- Factory Reset 36
- Expression Pedal Calibration 36
- Preset Level 37
- USB Setup 39
- Compressors 41
- Noise Gates 41
- Chorus Stompbox Models 42
- Vibrato / Rotary 44
- Envelope / Special 45
- Distortions 46
- Cabinets 52
- Section Six - Appendix 54
- Tone Library 55
- Effects Library 55
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 2.576 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais